1345L2，there are the best 1345L2 suppiers all over the world here.These are the list and detailed contact method of 1345L2 suppliers all over the world as follows.You can buy or get informations of 1345L2 through email , message or tel.

suppliers of 1345L2 and PDF data of 1345L2

Part Numbert	Mfg	Packt	D/C	Descriptiont	Qty	Company/Contact
1345L2	SOP-16	MOT	04+		7	GD TECH UK Contact:gdtechuk Tel:44-870-4866758 Fax:44-1212402714 Email: gdtechuk@gmail.com
1345L2	MOT		SOP-16			Sangsign Electronics (Hongkong.. Contact:KING Tel:86-755-82539762 Fax:86-755-82539762 Email: sales1@sangsign.com
1345L2	N/A	MOT	04+	N/A	5000	BestTopTechnologyCo.,Ltd Contact:Ms.WindyYe Tel:86-0755-33005684 Fax:86-0755-33202864 Email: windy@besttop-ic.com

1345L2 Datasheet

CHIP CLEAR: The contents of the entire memory of the AT28C64 may be set to the high state by the CHIP CLEAR operation. By setting CE low and OE t0 12 volts, the chip is cleared when a 10 msec low pulse is applied to WE.
1345L2 Price

The MAX6314 solves this problem by including a pull up transistor in parallel with the recommended 4.7kl resistor (Figure l). The pull-up resistor holds the output hig h until RESET is forced low by the pP reset l/0, or by the MAX6314 itself. Once RESET goes below 0.5V, a comparator sets the transition edge flip-flop, indicating
1345L2 on stock

SYMBOL	PARAMETER	CONDITIONS	MIN	TYP	MAX	UNIT
Viso,	R.M.S. isolation voltage from both terminals to external heatsink	f = 50-60 Hz; sinusoidal wavefo rm; R.H. " 65% ; clean and dustfree			2500	V
Ciso,	Capacitance from both terminals to external heatsink	f=l MHz		1 0		pF

Pin Names	Pin Type	Pin Description	Circuit Type	24- Pin Number	Shared Functions
PO.O-P0.7	I/O	I/O port with bit-programmable pins. Configurable to input or push-pull output mode. Pull-up resistors are assignable by software. Pins can be assigned individually as external interrupt inputs with noise filters, interrupt enable/ disable, and interrupt pending control. Interrupt with Reset(INTR) is assigned to Port 0.	1	5-12	INTO - INT4/INTR
P1.O-P1.7	I/O	I/O port with bit-programmable pins. Configurable to input mode or output mode. Pin circuits are either push-pull or n- channel open-drain type. Pull-up resistors are assignable by software.	2	13-20
P2.0 P2.1 P2.2	I/O	3-bit l/0 port with bit-programmable pins. Configurable to input mode, push-pull output mode, or n-channel open-drain output mode. Input mode with pull-up resistors are assignable by software. The two pins of port2 have high current drive capability.	3 4 5	21-23	REM/TOCK
XIN, XOUT		System clock input and output pins		2,3
TEST	I	Test signal input pin (for factory use only; must be connected to Vss).		4
VDD		Power supply input pin		24
VSS		Ground pin		1

ON Semiconductor and ;J are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. "Typical" parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical iinplant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.

Suppliers Datasheet
		Exact Matc