215005，there are the best 215005 suppiers all over the world here.These are the list and detailed contact method of 215005 suppliers all over the world as follows.You can buy or get informations of 215005 through email , message or tel.

suppliers of 215005 and PDF data of 215005

Part Numbert	Mfg	Packt	D/C	Descriptiont	Qty	Company/Contact
215005	LITTELFUSE		04+		2485	LZ ELECTRONICS,LTD Contact:vivian Tel:86-755-82500392 Fax: Email: vivian.lan@lzelectronics.com
215005	LITTELFUSE		04+	Time Lag Ceramic Tub	2485	A WELLMART ELECTRONICS CO., LT.. Contact:Tina Tel:886-2-22320272 Fax:886-2-29294087 Email: ext225@awellmart.com.tw
215005	LITT	FUSE_5X20			1019	Shenzhen Zhiruixin Technology .. Contact:mr.hou Tel:86-755-83213971 Fax:0755-83213973 Email: hlj20835@yahoo.com.cn

215005 Datasheet

AT49BV/LVOOIN(T) pin l for the DIP and PLCC packages and pin 9 for the TSOP package are don't connect pins. To allow for simple in-system reprogrammability, the AT49BV/LVO01(N)(T) does not require high input voltages for programming. Three-volt-only commands determine the read and programming operation of the device. Reading data out of the device is similar to reading from an EPROM; it has standard CE, OE, and WE inputs to avoid bus con- tention. Reprogramming the AT49BV/LVO01(N)(T) is per- formed by erasing a block of data and then programming on a byte-by-byte basis. The byte programming time is a fast 50 ps. The end of a program cycle can be optionally detected by the DATA polling feature. Once the end of a byte program cycle has been detected, a new access for a read or program can begin. The typical number of program and erase cycles is in excess of 10,000 cycles.
215005 Price

CS (Pin 3/Pin 3): Input to phase modulator for the LTC3722-1. Input to Pulse by Pulse and Overload Current Limit Comparators, Output of Slope Compensation Cir- cuitry. The pulse by pulse comparator has a nominal 300mV threshold, while the overload comparator has a nominal 600mV threshold.
215005 on stock

SYMBOL	PARAMETER	CONDITIONS	NOTES	TA = 25IC MIN TYP MAX	SUB- GROUP	-ssrc " TA " 125IC MIN TYP MAX	SUB- GROUP	UNITS
en	Input Noise Voltage	O.lHz t0 10Hz	4.5	0.25				ccVpP
	Input Noise Voltage Density	fo =10Hz fo = 30Hz fo = 1000Hz	3 4 4	8.0 5.6 4.5				n\U ddz n\U dfiZ n\U d4z
In	Input Noise Current Density	fo= 1000Hz	4.6	0.6				p\U gjdz
	Input Resistance Common Mode			2				Gl
	Input Voltage Range		4	+11		±10.2		V
CMRR	Common Mode Rejection Ratio	VCM = +11V VCM = +10V		100	1	94	2.3	dB dB
PSRR	Power Supply Rejection Ratio	VS = +4V to +18V VS = +4.5V to +18V		94	1	86	2.3	dB dB
AVOL	Large-Signal Voltage Gain	RL > 2k, Vo = +10V RL > 600l , Vo = +1V VS = +4V	4	700 200	4	300	5.6	\UmV \UmV
VOUT	Maximum Output Voltage Swing	RL = 2k RL = 600l		+11.5 +10.0	4 4	±10.5	5.6	V V
SR	Slew Rate	RL= 2k		1.7	7			V/c~
GBW	Gain-Bandwidth Product	fo =lOOkHz	4	5				MHz
Zo	Open-Loop Output Resistance	Vo =0,10 =0		70				l
PD	Power Dissipation			170	1			mW

0 1 0 ( u d ) r j S - I V N I V \ J J l N M L 8 J N \ f l l ' J \ f d W J

Suppliers Datasheet
		Exact Matc