| | | | LIMITS | |
| SYMBOL | PARAMETER | TEST CONDITIONS | Temp = -40YC to +85YC | UNIT |
| MIN | TYPi | MAX |
| | | Vcc = 2.3 t0 2.7V | 1 7 | 1.2 | | V |
| VIH | HIGH level Input voltage | Vcc = 2.7 t0 3.6V | 2 0 | 1.5 | |
| | | Vcc = 2.3 t0 2.7V | | 1.2 | 0.7 | V |
| VIL | LOW level Input voltage | Vcc = 2.7 t0 3.6V | | 1.5 | 0.8 |
| | | Vcc = 2.3 t0 3.6V; Vi = VIH or VIL; 10 = -100D:A | Vcc - 0.2 | Vcc | | V |
| Vcc = 2.3V; Vi = VIH or VIL; 10 = -6mA | Vcc - 0.3 | Vcc - 0.08 | |
| Vcc = 2.3V; Vi = VIH or VIL; 10 = -12mA | Vcc - 0.6 | Vcc - 0.26 | |
| VOH | HIGH level output voltage | Vcc = 2.7V; Vi = VIH or VIL; 10 = -12mA | Vcc - 0.5 | Vcc - 0.14 | |
| Vcc = 3.OV; Vi = VIH or VIL; 10 = -12mA | Vcc - 0.6 | Vcc - 0.09 | |
| Vcc = 3.OV; Vi = VIH or VIL; 10 = -24mA | Vcc - 1.0 | Vcc - 0.28 | |
| | | Vcc = 2.3 t0 3.6V; Vi = VIH or VIL; 10 = 1000:A | | GND | 0 20 | V |
| Vcc = 2.3V; Vi = VIH or VIL; 10 = 6mA | | O07 | 0 40 | V |
| VOL | LOW level output voltage | Vcc = 2.3V; Vi = VIH or VIL; 10 = 12mA | | O15 | 0 70 | V |
| Vcc = 2.7V; Vi = VIH or VIL; 10 = 12mA | | O14 | 0 40 |
| Vcc = 3.OV; Vi = VIH or VIL; 10 = 24mA | | 0.27 | 0 55 |
| Il | Input leakage current | Vcc = 2.3 t0 3.6V; VI = Vcc or GND | | O1 | 5 | A |
| loZ | 3-State output OFF-state current | Vcc = 2.3 t0 3.6V; Vi = VIH or VIL; VO = Vcc or GND | | O1 | 10 | ccA |
| lcc | Quiescent supply current | Vcc = 2.3 t0 3.6V; Vi = Vcc or GND; lo = 0 | | 0.2 | 40 | |
| Clcc | Additional quiescent supply current | Vcc = 2.3V t0 3.6V; Vi = Vcc - 0.6V; lo = 0 | | 150 | 750 | |
| | | Vcc = 2.3V; Vi = 0.7V | 45 | | | |
| IBHL2 | Bus hold LOW sustaining current | Vcc = 3.OV; Vi = 0.8V | 75 | 150 | | A |
| | | Vcc = 2.3V; Vi = 1.7V | -45 | | | |
| IBHH2 | Bus hold HIGH sustaining current | Vcc = 3.OV; Vi = 2.OV | -75 | -175 | | |
| IBHL02 | Bus hold LOW overdrive current | Vcc= 3.6V | 500 | | | ccA |
| IBHH02 | Bus hold HIGH overdrive current | Vcc= 3.6V | -500 | | | ccA |
| | | | | | |
| Parameters | Symbols | Ratings | Unit | Remarks |
| Supply voltage | VDC | -0.5 t0 20.0 | V | Ta= 25C |
| VDCB | -0.5 t0 20.0 | V |
| Analog RGB input signal | VIN1 | -2.5 t0 2.5 | V | Ta = 250C Voc = 9.5 V |
| Logic input voltage | VIN2 | -0.5 t0 5.5 | V |
| Storage temp. | TST | -40 t0 95 | C | |
| Operating temp. | TOP | -30 t0 85 | C | Note 1 |
| Relative humidity (RH) | 95 | % | Ta40C | no |
| 85 | % | 40< Ta50C | condensation |
| Absolute humidity | Absolute humidity shall not exceed Ta = 500C, RH = 85% | g/m3 | Ta> 50C |
| | | | | |
N8275F on stock Right to make changes - Philips Semiconductors reserves the right to make changes in the products - including circuits, standard cells, and/or software - described or contained herein in order to improve design and/or performance. When the product is in full production (status 'Production'), relevant changes will be communicated via a Customer Product/Process Change Notification (CPCN). Philips Semiconductors assumes no responsibility or liability for the use of any of these products, conveys no licence or title under any patent, copyright, or mask work right to these products, and makes no representations or warranties that these products are free from patent, copyright, or mask work right infringement, unless otherwise specified.
S E G 1 2 / P 1 0 . 0 S E G 1 1 / P 9 . 3 S E G 1 0 / P 9 . 2 S E G 9 / P 9 . 1 S E G 8 / P 9 . 0 S E G 7 / P 8 . 3 S E G 6 / P 8 . 2 S E G 5 / P 8 . 1 S E G 4 / P 8 . 0 S E G 3 / P 7 . 3 S E G 2 / P 7 . 2 S E G l / P 7 . 1 S E G O / P 7 . 0
