PC5-48-12，there are the best PC5-48-12 suppiers all over the world here.These are the list and detailed contact method of PC5-48-12 suppliers all over the world as follows.You can buy or get informations of PC5-48-12 through email , message or tel.

suppliers of PC5-48-12 and PDF data of PC5-48-12

Part Numbert

Mfg

Packt

D/C

Descriptiont

Qty

Company/Contact

PC5-48-12 Datasheet

After designing the IF match in simulation using the given S- parameters, some adjustment might be needed when implementing the match on the bench. At this point remember that the LO driver amplifier must be turned on since the lFA is directly coupled to the mixer FET. Figure 6 shows the circuit topology and component values designed for TriQuint's demo board. Figure 7 shows a typical AMPS IF output impedance.
PC5-48-12 Price

			V53C318165A
Symbol	Parameter	Access rime	Min	Typ.	Max	Unit	Test Conditions	Notes
1L	Input Leakage Current (any input pin)		-10		10		Vss " VIN " VCC + 0.3V	1
ILO	Output Leakage Current (for High-Z State)		-10		10		Vss " VOUT " VCC + 0.3V RAS, CAS at VIH	1
lccl	Vcc Supply Current,	50			200	mA	tRC = tRC (rTiin.)	2 3 4
	Operating	60			180
	Operating	70			160
ICC2	Vcc Supply Current, TTL Standby				2	mA	RAS, AS at VIH other inputs > Vss
ICC3	Vcc Supply Current,	50			200	mA	tRC = tRC (rTiin.)	2.4
	RAS-Only Refresh	60			180
	RAS-Only Refresh	70			160
ICC4	Vcc Supply Current,	50			90	mA	Minimum Cycle	2 3.4
	EDO Page Mode	60			75
	Operation	70			60
lcc5	Vcc Supply Current, CMOS Standby				1 0	mA	RAS > Vcc - 0.2 V, CAS > Vcc - 0.2 V	1
ICC6	Average Self Refresh Current CBR cycle with tRAS > tRASS min., (L-version only) CAS held low, WE = Vcc - 0.2V, Address and DIN = Vcc - 0.2V or 0.2V				1 0	mA
ICC7	Vcc Supply Current,	50			200	mA	tRC = tRC (rTiin)	2.4
	during CAS-before-RAS Refresh	60			180
	during CAS-before-RAS Refresh	70			160
VIL	Input Low Voltage		-0.5		0 8	V		1
VIH	Input High Voltage		2		Vcc+0.5	V		1
VOL	Output Low Voltage				0 4	V	IOL=2mA	1
VOH	Output High Voltage		2.4			V	IOH= -2 mA	1

PC5-48-12 on stock

Xicor products are covered by one or more of the following U.S. Patents: 4,326,134; 4,393,481 ; 4,404,475; 4,450,402; 4,486,769; 4,488,060; 4,520,461 ; 4,533,846 4,599,706; 4,617,652; 4,668,932; 4,752,912; 4,829,482; 4,874,967; 4,883,976; 4,980,859; 5,012,132; 5,003,197; 5,023,694; 5,084,667; 5,153,880; 5,153,691 5,1 61,137; 5,21 9,774; 5,270,927; 5,324,676; 5,434,396; 5,544,1 03; 5,587,573; 5,835,409; 5,977,585. Foreign patents and additional patents pending.

The device comes out of the HALT mode when the RESET pin is pulled low. In this case, the user has to ensure that the RESET signal is low long enough to allow the oscillator to re- start. An internal 256 te delay is normally used in conjunction with the two pin crystal oscillator. When the device comes out of the HALT mode through Multi-Input Wakeup, this de- lay allows the oscillator to stabilize. The following additional actions occur after the device

Suppliers Datasheet
		Exact Matc