PC74HCT377T，there are the best PC74HCT377T suppiers all over the world here.These are the list and detailed contact method of PC74HCT377T suppliers all over the world as follows.You can buy or get informations of PC74HCT377T through email , message or tel.

suppliers of PC74HCT377T and PDF data of PC74HCT377T

Part Numbert	Mfg	Packt	D/C	Descriptiont	Qty	Company/Contact
PC74HCT377T			08+/09+	全新原装，欢迎订购！	347	SHENG ZHOU HE ELECTRONICS CO.,.. Contact:zhou Tel:86-755-83397505.82883120 Fax:86-0755-88296852 Email: 1018686693@qq.com
PC74HCT377T		SOP	92	Original	347	Minchin WaiYip Development Co... Contact:Edison Chan Tel:86-755-61667059 Fax:86-755-61303859 Email: mingqindianzi@live.cn
PC74HCT377T			92+		347	Anichip International Ltd. Contact:Andrew Tel:86-755-25873776 Fax:86-755-25873736 Email: andrew@anichip.com
PC74HCT377T		SOP	92	new and original	347	WEIXIANG ELECTRONIC (HK) LIMIT.. Contact:Julie Tel:86-755-82814282 Fax:86-755-82814563 Email: wxic@wxic.net
PC74HCT377T	347				92	Majestic Trading Contact:dena Tel:86-755-83002395 Fax: Email: carmen@mtc-ic.com

PC74HCT377T Datasheet

R WORLD HEADQUARTERS: 233 Kansas St., El Segundo, California 90245, USA Tel: (310) 252-7105 TAC Fax: (310) 252-7309 Visit us at www.irf.com for sales contact information. 07/02
PC74HCT377T Price

		'aio_,]4I¨ii o h
PINS	NAME	DESCRIPTION
1	OE	Input for Output Enable (Active low). Enables transceiver driver to transmit data on the USB bus. When OE pin = LOW, driver circuitry is enabled.
2	RCV	Differential receiver output of D+ and D- input data lines. The output state of RCV is preserved and stable during an SEO condition.
3	VP	Single-ended D+ receiver output for detection of a single-ended zero or error conditions
4	VM	Single-ended D- receiver output for detection of a single-ended zero or error conditions.
5	SPND	Suspend input. Allows the device to enter a low power state while the USB is inactive.
6	MODE	Mode input. Selects between differential (VPO, VMO) and single-ended mode (Vo, FSEO).
7	Vcc	Supply voltage for digital I/O pins. Voltages supported: 1.65 t0 3.3V.
8	USB_DET	I/O level USB detect output. Logic High indicates that a USB cable is present.
9	D-	Negative USB data connection.
10	D+	Positive USB data connection. In full-speed connect mode, connect to VPU via a l.5kQ resistor. Tol- erance of this resistor is defined in the USB specification REV l.1 & 2.0
1 1	VPONO	Driver data input.
12	VMO/FSEO	Driver data input.
13	VREG	Regulated supply voltage output during USB operation of VBUS. luF decoupling capacitor is required.
14	VBUS	Supply voltage input. Can be directly connected to USB VBUS.
15	VPU	Pull-up supply voltage. Pin function is controlled by input ENUM.

PC74HCT377T on stock

Duty C

yce

0.2

__- .

_ -

0 1

--__

___

0.05 0.02

_7 J

·- -l

r l Sir

iglel

iulsE

ELECTRICAL CHARACTERISTIC ( TA = - 55 IC to +125 IC, Unless Otherwise Specified )
Parameter	Symbol	Min	Typ.	Max	Units	Test Conditions	Fig.	'xlote
Current Transfer Ratio Logic High Output Current Logic Low Supply Current Logic High Supply Current Input Forward Voltage Input Reverse BreakdownVoltage Input to Output Leakage Current Propagation Delay Time LogicHigh to Low Logic Low to High Common Mode Trasient immunity Logic High Level Logic Low Level	CTR I OH I CCL I CCH VF BVR I i-o t PHL t PLH CMH CML	9 3	25 .05 40 .05 1.7 0.3 0.8 >1 >1	100 200 10 2.5 1.0 2.0 6.0	% V V ccS ccS KV KV	IF=16 mA, Vo=0.4 V, Vcc=4.5 V IF=OmA, Vo=Vcc=15V IF=lOmA, Vcc=15V, Vo=open IF=OmA, Vcc=15V, Vo=open IF=10 mA IR=10 Relative Humidity " 45%, TA = 25IC, V i_o = 1000 Vdc /, k'168.2IVC::550Vp,F IF=O, RL=8.2KI ,VCM=10V p-p IF=16, RL=8.2KI ,VCM=10V p-p	2 1 3,4 3,4	2 1

Suppliers Datasheet
		Exact Matc