R1131N271A-TR-F，there are the best R1131N271A-TR-F suppiers all over the world here.These are the list and detailed contact method of R1131N271A-TR-F suppliers all over the world as follows.You can buy or get informations of R1131N271A-TR-F through email , message or tel.

suppliers of R1131N271A-TR-F and PDF data of R1131N271A-TR-F

Part Numbert

Mfg

Packt

D/C

Descriptiont

Qty

Company/Contact

R1131N271A-TR-F Datasheet

Output Detector (each cbannei} Supply Voltage - Vcc .. ........ 7V (1 Minute Maximum) Current -lo .., . 25mA Collector Power Dissipation . . :. I .. ... 40mW Voltage - Vo .. .... 7V
R1131N271A-TR-F Price

PIN NO.	I/O	SIGNAL	PIN NO.	I/O	SIGNAL	PIN NO.	I/O	SIGNAL	PIN NO.	I/O	SIGNAL
1	O	OUT9	1 3	l	TIN4	25	l	CV9	37	l	OVD
2	O	OUT8	14	l	TIN3	26	l	CV8	38	l	TMOD4
3	O	OUT7	1 5	l	TIN2	27	l	CV7	39	l	TMOD3
4	O	OUT6	16	l	TMOD1	28	l	CV6	40	l	TMOD2
5	O	OUT5	1 7	O	TOUT	29	l	CV5	41	l	GH
6		GND	1 8		GND	30	l	CV4	42		GND
7	O	OUT4	1 9		VDD	31		GND	43		VDD
8	O	OUT3	20	l	FSC8	32	l	CV3	44	l	FSC4
9	O	OUT2	21	l	CLR	33	l	CV2	45	l	TMODO
1 0	O	OUT1	22	l	DCSY	34	l	CV1	46	l	PAL/ NT
1 1	O	OUTO	23	O	DSSY	35	l	CVO	47	l	TIN1
12	O	OPARI	24	O	DRSY	36	l	IPARI	48	l	TINO

R1131N271A-TR-F on stock

Pin No.
44L SOP (A23L2616)	48L TSOP (A23L2616)	48L TSOP (A23L26161)	Symbol	Description
1-11, 34-44	2-23	1-10, 15-25, 48	AO-A21	Address Inputs
15-22, 24-30	28-35, 39-45	29-36, 38-44	00-014	Data Outputs
31	46	45	015/A-1	Output 15(WORD mode) /LSB Address (BYTE mode)
12	24	26	CE	Chip Enable Input
14	27	28	OE	Output Enable Input
33	1	47	BYTE	BYTE or WORD mode Selection
23	37-38	37	VCC	Power Supply
13, 32	25-26,47-48	27, 46	GND	Ground
1	36	11-14	NC	No Connection

When using phase comparatorI, the loop filter frequency response may be used to limit the capture range of the loop, that is the range of input frequencies that the loop will lock onto. This property may be used to provide a degree of selectivity if required. The following table shows filter component values for various capture ranges. It should be noted that the loop filter used here is the simple 'lag' filter (i.e. R2 = O), this is to minimise ripple at 2 x fir on the loop filter output which would cause frequency modulation of the switched capacitor filter response.

Suppliers Datasheet
		Exact Matc