RSD-1524DH，there are the best RSD-1524DH suppiers all over the world here.These are the list and detailed contact method of RSD-1524DH suppliers all over the world as follows.You can buy or get informations of RSD-1524DH through email , message or tel.

suppliers of RSD-1524DH and PDF data of RSD-1524DH

Part Numbert	Mfg	Packt	D/C	Descriptiont	Qty	Company/Contact
RSD-1524DH	recompower	New origin	08+		500	HK United Electronics Dev.Ltd .. Contact:franken Tel:86-755-83633553 Fax: Email: franken@united-ic.com

RSD-1524DH Datasheet

V65-5v

-10V

T-mb.25'c

-15V

RSD-1524DH Price

After the stop bit is detected, the receiver will immediately look for the next start bit. However, if a non-zero character was received without a stop bit (framing error) and RxD remains LOW for one half of the bit period after the stop bit was sampled, then the receiver operates as if a new start bit transition had been detected at that point (one-half bit time after the stop bit was sampled).
RSD-1524DH on stock

Symbol	Parameter	Min	Typ.	Max	Unit
Vio	Input Offset Voltage + Vic = Vicm min., VCC+ = 5V t0 10V - (note l) Tmin. " Tamb " Tmax.		1.2	5 6.5	mV
lio	Input Offset Current - (note 2) Vic = 2.5 V Tmin. " Tamb " Tmax.		1	300	pA
lib	Input Bias Current - (note 2) Vic = 2.5 V Tmin. " Tamb ', Tmax.		1	600	pA
Vicm	Input Common Mode Voltage Range Tmin. " Tamb " Tmax.	0 to Vcc+-1.2 0 to Vcc+ -1.5			V
CMR	Common-mode Rejection Ratio Vic = Vicm min		82		dB
SVR	Supply Voltage Rejection Ratio Vcc' = +5V to +10V		90		dB
VOH	High Level Output Voltage Vid = 1V, IOH =-4mA Tmin. " Tamb " Tmax.	4.5 4.3	417		V
VOL	Low Level Output Voltage Vid = -1V, 101= 4mA Tmin. " Tamb " Tmax.		220	300 375	mV
lcc	Supply Current (2 comparators) No load - Outputs low Tmin. " Tamb " Tmax.		18	40 50
tPLH	Response Time Low to High Vic = OV, f = 10kHz, CL = 50pF, Overdrive = 5mV Overdrive = 10mV Overdrive = 20mV Overdrive = 40mV TTLlnput		1.5 1.1 0.9 0.7 0.6		ocs
tPHL	Response Time High to Low Vic = OV, f = 10kHz, CL = 50pF, Overdrive = 5mV Overdrive = 10mV Overdrive = 20mV Overdrive = 40mV TTLlnput		2.2 1.6 1.1 0.75 0.17		ocs
tf	Fall time f = 10kHz, CL = 50pF, Overdrive 50mV		30		ns

Note: 1. Except for the rating "Operating Temperature Range", stresses above those listed in the Table "Absolute Maximum Ratings" may cause permanent damage to the device. These are stress ratings only, and operation of the device at these or any other conditions above those indicated in the Operating sections of this specification is not implied. Exposure to Absolute Maximum Rating condi- tions for extended periods may affect device reliability. Refer also to the ST SU RE Program and other relevant quality documents. 2. MIL-STD-883C, 3015.7 (100 pF, isoo I )

Suppliers Datasheet
		Exact Matc