RSZ-2005P，there are the best RSZ-2005P suppiers all over the world here.These are the list and detailed contact method of RSZ-2005P suppliers all over the world as follows.You can buy or get informations of RSZ-2005P through email , message or tel.

suppliers of RSZ-2005P and PDF data of RSZ-2005P

Part Numbert	Mfg	Packt	D/C	Descriptiont	Qty	Company/Contact
RSZ-2005P	recompower	New origin	08+		500	HK United Electronics Dev.Ltd .. Contact:franken Tel:86-755-83633553 Fax: Email: franken@united-ic.com

RSZ-2005P Datasheet

Electrical Characteristics

Average forward current I F(AV) 1.0 Amps TA = 1300 iare wave, RejC = 150C/w Maximum surge current I FSM 50 Amps 8.3ms, 5hOal(;'sSqeuafJ = 1500C Max peak forward voltage VFM .39 Volts IFM = O.lA:Tj = 250C* Max peak forward voltage VFM .58 Volts IFM = l.OA:Tj = 250C* Typicalkjunction capacitance IRCjl60pFA VRVR,-'5.Oy,TJ = 25aC *Pulse test: Pulse width 300 /usec. Duty cycle 2%

RSZ-2005P Price

				LIMITS
SYMBOL	PARAMETER	TEST CONDITIONS		Temp = 40IC to +85YC			UNIT
SYMBOL	PARAMETER	TEST CONDITIONS		MIN	TYPi	MAX	UNIT
VIK	Input clamp voltage	Vcc = 2.7V; IIK = -18mA				-1.2	V
		Vcc = 2.7 t0 3.6V; IOH = -1000:A		Vcc-0.2			V
VOH	High-Ievel output voltage	Vcc = 2.7V; IOH = -8mA		2 4
VOH	High-Ievel output voltage	Vcc = 3.OV; IOH = -32mA		2 0
		Vcc = 2.7V; IOL = 1000:A				0 2	V
		Vcc = 2.7V; IOL = 24mA				0 5
VOL	Low-Ievel output voltage	Vcc = 3.OV; IOL = 16mA				0 4
		Vcc = 3.OV; IOL = 32mA				0 5
		Vcc = 3.OV; IOL = 64mA				0 55
		Vcc = 3.6V; Vi = Vcc or GND	Control pins			+1
		Vcc = 0 0r 3.6V; Vi = 5.5V				10
II	Input leakage current	Vcc = 3.6V; Vi = Vcc				1
II	Input leakage current	Vcc = 3.6V; Vi = 0	Data pins4			5
IOFF	Output off current	Vcc = OV; Vi or Vo = 0 t0 4.5V				±100
		Vcc = 3V; Vi = 0.8V		75
IHOLD	Bus Hold current A inputs	Vcc = 3V; Vi = 2.OV		-75			e
IEX	Current into an output in the High state when Vo > Vcc	Vo = 5.5V; VCC = 3.OV				125
lPUPD	Power up/down 3-State output current3	Vcc " 1.2V; Vo = 0.5V to Vcc; Vi = GND or Vcc; OE/OE = Don't care				+100
IOZH	3-State output High current	Vcc = 3.6V; Vo = 3.OV; Vi = VIL or VIH				5
IOZL	3-State output Low current	Vcc = 3.6V; Vo = 0.5V; Vi = VIL or VIH				-5
ICCH		Vcc = 3.6V; Outputs High, Vi = GND or Vcc,lo = 0			O13	0 12
ICCL	Quiescent supply current	Vcc = 3.6V; Outputs Low, Vi = GND or Vcc,lo = 0			3 5	5	mA
lccZ	Quiescent supply current	Vcc = 3.6V; Outputs Disabled; Vi = GND or Vcc, lo = 0			O13	0 12	mA
Clcc	Additional supply current per input pin2	Vcc = 3V t0 3.6V; One input at Vcc-0.6V, Otherinputs at Vcc or GND				0 2	mA

RSZ-2005P on stock

DIM	MILLIMETERS
A	2.00±0.20
Al	1 3±0l
B	2.1±0.1
B1	1.250.1
C	0 65
D	0 2+0 10/-0.05
G	0-0l
H	0 9±0.1
T	0 15+0.1/-0.05

Pin Number	Pin Name	Pin Function
1.4	EN	Enable (Input): Logic-compatible enable input. High input > 2.4V. Low input <0.8V (-1, -3 active high, -2, -4 active low). Do not float.
2.3	FLG	Fault Flag (Output): Active-Iow open-drain output. Indicates overcurrent, UVLO, OVLO and thermal shutdown.
6	GND	Ground: Supply return
7	IN	Supply Input: Output MOSFET drain. Also supplies lC's internal circuitry. Connect to positive supply.
5 and 8	OUT	Switch Output: Output MOSFET source. Typically connect to switched side of load.

Suppliers Datasheet
		Exact Matc