RT0603DRD07150KL，there are the best RT0603DRD07150KL suppiers all over the world here.These are the list and detailed contact method of RT0603DRD07150KL suppliers all over the world as follows.You can buy or get informations of RT0603DRD07150KL through email , message or tel.

suppliers of RT0603DRD07150KL and PDF data of RT0603DRD07150KL

Part Numbert

Mfg

Packt

D/C

Descriptiont

Qty

Company/Contact

RT0603DRD07150KL Datasheet

f	S11		S21		S12		S22
(MHz)	Mag	Ang	Mag	Ang	Mag	Ang	Mag	Ang
100 200 300 400 500 600 700 800 900 1000 1100 1200 1300 1400 1500 1600 1700 1800 1900 2000 2100 2200	0.874 0.837 0.844 0.850 0.858 0.864 0.868 0.870 0.879 0.887 0.898 0.905 0.911 0.914 0.916 0.918 0.923 0.928 0.933 0.937 0.935 0.934	-58 -70 -100 -118 -130 -139 -146 -153 -158 -162 -167 -171 -174 -178 179 176 173 171 168 165 162 159	24.1 21.8 17.5 14.1 11.5 9.44 7.86 6.61 5.65 4.86 4.24 3.73 3.30 2.92 2.61 2.35 2.14 1.95 1.79 1.65 1.53 1.43	137 129 106 89 77 66 56 48 40 33 26 20 14 8 2 -3 -8 -13 -18 -23 -28 -33	0.009 0.010 0.012 0.013 0.012 0.011 0.009 0.008 0.006 0.004 0.004 0.004 0.005 0.006 0.008 0.009 0.011 0.013 0.015 0.017 0.018 0.020	46 37 21 9 -1 -8 -13 -15 -13 -2 19 48 66 74 77 79 79 78 76 74 71 68	0.770 0.737 0.710 0.709 0.723 0.749 0.767 0.782 0.801 0.815 0.837 0.854 0.870 0.882 0.892 0.898 0.907 0.914 0.920 0.925 0.929 0.934	-35 -42 -62 -77 -88 -98 -108 -116 -123 -130 -136 -141 -147 -152 -156 -160 -164 -168 -172 -176 -179 178

RT0603DRD07150KL on stock

(VDD = 3.OV, OVDD = 1.8V, VREFIN = VDD (internal reference), CL ~ 10pF at digital outputs, fCLK = 45MHz, CREFP = CREFN = CCOM 0.33pF, TA = -400C to +850C, unless otherwise noted. Typical values are at TA=+250C.) (Note l) Note l: Specifications >+250C guaranteed by production test, <+250C guaranteed by design and characterization. Note 2: SNR, SINAD, SFDR, HD3, and THD are based on a differential analog input voltage of -0.5dB FS referenced to the amplitude of the digital output. SNR and THD are calculated using HD2 through HD6. Note 3: The power consumption of the output driver is proportional to the load capacitance (CL). Note 4: Guaranteed by design and characterization. Not production tested. Note 5: SINAD settles to within 0.5dB of its typical value. Note 6: Crosstalk rejection is measured by applying a high-frequency test tone to one channel and a low-frequency tone to the second channel. FFTs are performed on each channel. The parameter is specified as power ratio of the first and second channel FFT test tone bins. Note 7: Amplitude/phase matching is measured by applying the same signal to each channel, and comparing the magnitude and phase of the fundamental bin on the calculated FFT.

Suppliers Datasheet
		Exact Matc