RT9167A33CS，there are the best RT9167A33CS suppiers all over the world here.These are the list and detailed contact method of RT9167A33CS suppliers all over the world as follows.You can buy or get informations of RT9167A33CS through email , message or tel.

suppliers of RT9167A33CS and PDF data of RT9167A33CS

Part Numbert

Mfg

Packt

D/C

Descriptiont

Qty

Company/Contact

RT9167A33CS Datasheet

Parameter	Frequency (MHz)	Typical@ 250C	Specification @25C	Spec. over - 400C to +850C
Passband Insertion Loss	1920 - 1980	1.9	2.2 dB max.	2.4 dB max.
Passband Ripple	1920 - 1980	0.6	0.75 dB max.	0.9 dB max.
Passband Return Loss	1920 - 1980	15.0	10.0 dB min.	10.0 dB min.
Attenuation:	1 900	18.0	15.0 dB min.	15.0 dB min.
	2000	18.0	15.0 dB min.	15.0 dB min.
	2110 - 2170	40.0	35.0 dB min.	35.0 dB min.
Power into any port	2 Watt max.	Note: Supplier shall test each filter to the critical electrical specifications of the above table. Any subsequent audits may deviate from in value due to measu repeatability among different test systems. Such deviations shall not exceed the following limits: Specification Allowance Insertion Loss 0.1 dB Return Loss l.0 dB Stopbands l.0 dB	Document No. 008-0256-0	Page l of 2

RT9167A33CS Price

The 1519-series device is a fixed, single-input, ten-output, passive delay line. The signal input (IN) is reproduced at the outputs (T1-T10) in equal increments. The delay from IN to T10 (TD) is given by the device dash number. The characteristic impedance of the line is given by the letter code that follows the dash number (See Table). The rise time (TR) of the line is 20% of TD, and the 3dB bandwidth is given by l.75 / TD.
RT9167A33CS on stock

PARAMETER	CONDITIONS		MIN TYP MAX	UNITS
Input Voltage			1 8 3 6	V
Input Undervoltage Lockout Voltage			0 8 1 6	V
	2V < VIN < 3.3V,	TA = OoC to +850C	3.17 3.3 3.43	V
Output Voltage	OmA < IOUT < 20mA	TA = -400C to +850C	3 .15 3.45	V
Output Current	VIN = 1.8V, VOUT > 3.17V		20	mA
No-Load Supply Current	VIN = 2.5V, FSET = IN or GND		50 80	UA
Leakage Current into OUTin Shutdown	VOUT = 3.6V, SHDN = GND		15 25	UA
Supply Current in Shutdown	VIN= 3.3V		1 5	UA
FSET, SHD I Input Voltage Low	VIN= 1.8V		0.5 x 0.3 x VIN VIN	V
FSET, SHD I Input Voltage High	VIN= 3.6V		0.7 x 0.5 x VIN VIN	V
FSET, SHDN Input Leakage Current	FSET SHDKI = GND orVIN		0.1 1	UA
	FSET= GND		260 330 450
Switching Frequency	FSET= IN		700 1000 1300	kHz
Output Short-Circuit Current	OUT = GND, VIN = 3.3V		100 200	mA
Efficiency	VIN = 2V, IOUT = 10mA		80	%

Parameter	Symbol	Min	Typ	Max	Units
Crystal Frequency T1 CCITT (Note 5)	fc		6.176000 8.192000		MHz
CLKIN Frequency T1 CCITT (Note 6)	n		1.544 2.048		MHz
CLKOUT Frequency T1 CCITT (Note 6)	fout		1.544 2.048		MHz
Clock Pulse Width T1	tpwh tpwl		324 324		ns
CCITT (Note 7)	tpwh tpwl		244 244		ns
Acceptable CLKIN range (Note 8)			+130		ppm
Duty Cycle (Note 9)			50		%
Rise Time, All Digital Outputs (Note 10)	tr		36	100	ns
Fall Time, All Digital Outputs (Note 10)	tf		1 7	100	ns
DIN to CLKIN Falling Setup Time	tsu	30			ns
CLKIN Falling to DIN Hold Time	th	50			ns
CLKOUT Falling to DOUT Propogation Delay	tphl			200	ns

Suppliers Datasheet
		Exact Matc