| Part Numbert | Mfg | Packt | D/C | Descriptiont | Qty | Company/Contact | |
| SKKT57-08D | SEMIKRON | NA | 100 |
|
 |
||
| SKKT57-08D | SEMIKRON | 50 |
|
|
|||
| SKKT57-08D | 西门康 | 50 | 模块 |
|
|
||
| SKKT57-08D | SEMIKRON | MODULE | N/A | STOCK | 100 |
|
|
| SKKT57-08D | 西门康 | new and or | 06+ | 321 |
|
||
| SKKT57-08D | SEMIKRON | MODULES | 05+ | 30 |
|
|
|
| SKKT57-08D | SEMIKRON | Module | N/A | SCR | 50 |
|
|
| SKKT57-08D | Semitrans | 45 |
|
||||
| SKKT57-08D | SEMIKRON | MODULE | N/A | 100 |
|
||
| SKKT57-08D | N/A | 50 |
|
||||
| SKKT57-08D | N/A | module | 2008+ | 50 |
|
|
|
| SKKT57-08D | SEMIKRON | Module | new and original | 30 |
|
|
|
| SKKT57-08D | SEMIKRON | NEW | 100 |
|
|||
| SKKT57-08D | 西门康 | 模块 | 代理原装 | 382 |
|
||
| SKKT57-08D | MODULE | SEMIKRON | 50 |
|
|||
| SKKT57-08D | SEMIKRON | 05+ | new and original | 30 |
|
||
| SKKT57-08D | SEMIKRON | MODULE | 06+ | 50 |
|
||
| SKKT57-08D | Power modu | N/A | New & Original/stock | 100 |
|
||
| SKKT57-08D | SEMIKRON | MODULE | 42 |
|
|||
| SKKT57-08D | N/A | STOCK | 05+ | 186 |
|
||
| SKKT57-08D | 50 |
|
|||||
| SKKT57-08D | SEMIKRON | MODULE IGB | 04+ | MODULE IGBT | 64 |
|
|
| SKKT57-08D | SEMIKRON | 55 |
|
||||
| SKKT57-08D | Power modu | N/A | New & Original/stock | 100 |
|
||
| SKKT57-08D | 西门康 | 50 |
|
||||
| SKKT57-08D | 50 |
|
|||||
| SKKT57-08D | SEMIKRON | STOCK | 500 |
|
|||
| SKKT57-08D | SEMIKRON | 30 |
|
||||
| SKKT57-08D | SEMIKRON | callmeanytime | 55 |
|
|||
| SKKT57-08D | SEMIKRON | module | 2005+ | 200 |
|
||
| SKKT57-08D | SEMIKRON | MODULE | 00+ | 50 |
|
|
SKKT57-08D Datasheet The LISl R02 is a complete rotational accelerometer system based on a architecture, followed by a digital downsampling block and a digital filter, featur- ing high sensitivity, 800 Hz signal bandwidth and a complete serial port interface for a direct connection SKKT57-08D Price
SKKT57-08D on stock The BBA's primary mounting surface is eight pads located on the bottom of the module. Since these pads are inaccessible during mounting, castellations that run up the side of the module have been provided to facilitate solder wicking to the module's underside. If the recommended pad placement has been followed, the pad on the board will extend slightly past the edge of the module.Touch both the PCB pad and the module castellation with a fine soldering tip. Tack one module corner first, The 1516-series device is a fixed, single-input, five- output, passive delay line. The signal input (IN) is reproduced at the outputs (T1-T5) in equal increments. The delay from IN to T5 (TD) and the characteristic impedance of the line (Z) are determined by the dash number. The rise time (TR) of the line is 30% of TD, and the 3dB bandwidth is given by l.05 / TD. The device is available in a 8-pin DIP (1516) or a 8-pin SMD (1516S), and a wide range of pinouts may be specified. |
