| PARAMETER | SYMBOL | CONDITIONS | MIN TYP MAX | UNITS |
| Multitone Spurious-Free Dynamic Range Within a Window | | 8 tones at 2.1MHz spacing, fCLK = 165MHz, fOUT = 28.3MHz t0 45.2MHz, span = 50MHz | 70 | dBc |
| Adjacent Channel Power Ratio with UMTS | ACLR | fOUT = 30.72MHz, RBW = 30kHz, fCLK = 122.88MHz | 65 5 | dB |
| | | | fOUT= 10MHz | -76 | |
| fCLK = 165MHz, | fOUT= 20MHz | -74 |
| AOUT = -1dBFS | fOUT= 40MHz | -71 |
| Total Harmonic Distortion to | | fOUT= 10MHz | -75 |
| Nyquist (2nd- Through 8th-Order | THD | fCLK = 100MHz, | fOUT= 20MHz | -74 | dBc |
| Harmonics Included) | AOUT = -1dBFS | fOUT= 30MHz | -73 |
| fCLK = 25MHz, AOUT = -1dBFS | fOUT= 1MHz | -76 |
| Output Channel-to-Channel lsolation | | fOUT= 10MHz | 90 | dB |
| Channel-to-Channel Gain Mismatch | | fOUT = 10MHz, G[3:0] = 1000 | 0 025 | dB |
| Channel-to-Channel Phase Mismatch | | fOUT= 10MHz | 0 05 | Degrees |
| | | fCLK = 165MHz, fOUT = 10MHz, IFS = 20mA | 60 5 | |
| fCLK = 165MHz, fOUT = 10MHz, IFS = 5mA | 61 |
| Signal-to-Noise Ratio to Nyquist | SNR | fCLK = 65MHz, fOUT = 10MHz, IFS = 20mA | 62 | dB |
| fCLK = 65MHz, fOUT = 10MHz, IFS = 5mA | 62 |
| | | Interleaved mode disabled, IDE = 0 | 165 200 | |
| Maximum DAC Conversion Rate | fDAC | Interleaved mode enabled, IDE = 1 | 82 5 100 | Msps |
| Glitch Impulse | | | 5 | pV-s |
| Output Settling Time | tS | To +0.1% error band (Note 3) | 12 | ns |
| Output Rise Time | | 10% t0 90% (lxlote 3) | 2 2 | ns |
| Output Fall Time | | 90% t0 10% (lxlote 3) | 2 2 | ns |
| ANALOG OUTPUT |
| Full-Scale Output Current Range | IFS | | 2 20 | mA |
| Output Voltage Compliance Range | | | -1.00 +1.25 | V |
| Output Leakage Current | | Shutdown or standby mode | 5+5 | UA |
| REFERENCE |
| Internal-Reference Output Voltage | VREFO | REN =0 | 1 13 1 24 1 32 | V |
| | | | | |
5.4 INTERNAL LOGIC, OVER CURRENT PROTECTION (OCP) AND INTERLOCKING FUNCTION. The DIM (Digitallnput Monitor) block manages the input signals delivered to the drivers ensuring that they are low during the described start-up procedure; the DIM block controls the L6382D5 behaviour during both save and operating modes.
SKM40GD-124D on stock Transient Response l A/ps load step, 50 t0 100 % Iomax, Cout =330 pF tti RecoveryTime - 70 OVtr Voover/undershoot - 120
1)Worstcase package 2) Max nu rrber of outputs defined as (n). Data inpr_ts are d riven OV t0 3.3V, (n -1) outputs switching and one ouput at GND 3) max nuner of data inputs (n) switching. (n-l) switching OV t0 3.3V. Inputs under test switching: 3.3V to threshold (VILO), OV to threshold (VIHD).f=lM Hz
