SL6310CMP，there are the best SL6310CMP suppiers all over the world here.These are the list and detailed contact method of SL6310CMP suppliers all over the world as follows.You can buy or get informations of SL6310CMP through email , message or tel.

suppliers of SL6310CMP and PDF data of SL6310CMP

Part Numbert	Mfg	Packt	D/C	Descriptiont	Qty	Company/Contact
SL6310CMP	ZARLINK	SOP8			188	A-RICH HK LECTRON CO.,LIMITED Contact:JING ZHOU Tel:86-755-33377586 Fax:86-755-33377578 Email: ARICH2@yahoo.cn

SL6310CMP Datasheet

Parameter	Symbol	Min	Fyp	Max	U nit	Conditions	Measurement circuit
Power save current	IST		0	10	uA	OFF mode	Fig.4
Output voltage	Voi	4 75	5 0	5 25	v		Fig.l
Input stability	Reg.l		20	100	mV	Vcc=6~2=5V	Fig.l
Ripple rejection rati	R.R	45	55		dB	eiN=lVrms, f=120Hz, lo=lOOmA	Fig.2
Load regulation	Reg.L		50	150	mV	lo=5mA-÷1A	Fig.l
Temperature coefficient of output voltage	Tcv		+0.02		% /'c	lo=5mA, Tj=0~125'C	Fig.l
Minimum l/0 voltage differential	Vd		0 3	0 5	V	Vcc=4.75V	Fig.3
Bias current	\|D		2 5	5 0	mA	lo=OmA	Fig.4
Peak output current	lO-P	1 0	1 5		A	Tj=25C	Fig.l
Output short-circuit current	los		0 4		A	Vcc=25V	Fig.5
ON mode voltage	Vthl	2 0			V	Output Active mode, lo=OmA	Fig.6
OFF mode voltage	Vth2			0 8	V	Output OFF mode, lo=OmA	Fig.6
Input high level current	¨	100	200	300	uA	CTL=5V, lo=OmA	Fig.6

SL6310CMP Price

		Test		Limits
Parameter	Symbol	Pin	Test Conditions	Min	Typ	Max	Units
Supply Voltage	VDD	2	Operating	6	9	16	V
Supply Current	IDD1	2	HRNEN,LEDEN and FEED=OV			100	nA
Input Voltage Low	VIL1	3,8				1	V
Input Voltage High	VIH1	3,8		2.3			V
Input Leakage Low	IIL1	3,8	Vin=VSS			-100	nA
Input Leakage Low	ILFD	4	FEED=-10V			-50	uA
Input Leakage High	IIH1	3.8	Vin=VDD			100	nA
Input Leakage High	IHFD	4	FEED=22V			50	uA
Output Voltage Low	VOL1	6,7	101=16mA		3	5	V
	VOL2	6,7	101=16mA, VDD=7.2V			9	V
	VOL3	1	lol=lOmA, VDD=7.2V		5	1	V
Output Voltage High	VOhl	6,7	loh=-16mA	8.5	8.7		V
Output Voltage High	VOh2	6,7	loh=-16mA, VDD=7.2V	6.3			V

SL6310CMP on stock

1. Typical characteristics are at TA = 250C. 2. These are absolute values with respect to device ground and all overshoots due to system or tester notice are included 3. Fmax = 1/tRC . 4. IccsBi is 2.OuA/3.OuA at Vcc=2.OV/3.OV and TA=700C. 5. VIL = -1.5V for pulse width less than 30ns

l l le=

·_-- - J .2 Iv

0.2

___

-N -_ J

___

0 1 0 05 l __- 0 02 7 l j

e Pul

I l

10-4 10-3 10-2

10-1 1 Square Wave Pulse Duration (sec)

Suppliers Datasheet
		Exact Matc