MOTMap-5  > SXI-1014-28PLLP

suppliers of SXI-1014-28PLLP and PDF data of SXI-1014-28PLLP

Part Numbert Mfg Packt D/C Descriptiont Qty Company/Contact  
SXI-1014-28PLLP SENSONIX    2007+ROHS    953 
    BONASE(HK) ELECTRONICS CO., L..
  • Contact:Vincent
  • Tel:86-0755-82579312
  • Fax:86-0755-83239040
  • Email: bonase@vip.163.com
SXI-1014-28PLLP SENSONIX  QFN  07+    985 
    ICON INTERNATIONAL (HK) CHIPS ..
  • Contact:Lin
  • Tel:86-755-23816108
  • Fax:86-755-23816109
  • Email: ruishengic@163.com
SXI-1014-28PLLP SENSONIX  QFN  07+  ORIGINEL  985 
    MTE ELECTRONICS CO
  • Contact:Klien
  • Tel:86-754-84484548
  • Fax:
  • Email: mte668@gmail.com
SXI-1014-28PLLP 985  ORIGINAL  SENSONIX    07+ 


SXI-1014-28PLLP n/a  QFN  n/a  NEW AND ORIGINAL To:  1005 
    SunPlus Electronics co.
  • Contact:David
  • Tel:86-755-83677874
  • Fax:86-755-83677875
  • Email: david@sunplusic.com


SXI-1014-28PLLP 985  NEW & STOC  SENSONIX    07+ 
SXI-1014-28PLLP SENSONIX  QFN  07+  进口原装自家库存  985 
    Shenzhen Guoyuan Eiectronics C..
  • Contact:Mr.su
  • Tel:86-755-23816266/23816225
  • Fax:0755-33062278
  • Email: suweigong@126.com

SXI-1014-28PLLP Datasheet
An internal 2-bit DAC allows LED currentto be adjusted for LED brightness control. The LTC3202 also has thermal shutdown protection and can survive a continuous short- circuit from VOUT to GND. Built-in soft-start circuitry prevents excessive inrush current during start-up. High switching frequency enables the use of small external capacitors. A low current shutdown feature disconnects the load from VIN and reduces quiescent current to less thanl
SXI-1014-28PLLP Price

Pin (SOIC/MSOP/DIP) Name Function
1 NC No internal connections
2 NC No internal connections
3 RESET/RESET Reset Output. RESET is an active LOW, open drain output which goes active whenever Vcc falls below VTRIP. It will remain active until Vcc rises above the VTRIP for tPURST RESET/RESET goes active if the Watchdog Timer is enabled and SDA remains either HIGH or LOW longer than the selectable Watchdog time out period. RESET/RESET goes active on power-uppower-up and remains active for 250ms after the power supply stabilizes. RESET is an active high open drain output. An external pull up resistor is required on the RESET/RESET pin.
4 VSS Ground
5 SDA Serial Data. SDA is a bidirectional pin used to transfer data into and out of the device. It has an open drain output and may be wire ORed with other open drain or open collector outputs. This pin requires a pull up resistor and the input buffer is always active (not gated).
6 SCL Serial Clock. The Serial Clock input controls the serial bus timing for data input and output.
7 WP Write Protect. WP HIGH prevents writes to any location in the device (including the control register). Connect WP pin to Vss when it is not used.
8 Vcc Supply Voltage


SXI-1014-28PLLP on stock

7 -'-- -_ ---- -18V
-'- --- ---- --- --- - .30V .40v
oow


J KJI L T 1 DEVICEADDRESS DATAE;YTE Jr DATAB'(TE l DATABYTE L f
IIIIII IIIIII 1 A A A I11PI
T 1L ^J^^l^^6