SY100EP140LZI，there are the best SY100EP140LZI suppiers all over the world here.These are the list and detailed contact method of SY100EP140LZI suppliers all over the world as follows.You can buy or get informations of SY100EP140LZI through email , message or tel.

suppliers of SY100EP140LZI and PDF data of SY100EP140LZI

Part Numbert

Mfg

Packt

D/C

Descriptiont

Qty

Company/Contact

SY100EP140LZI Datasheet

Symbol Characteristic Conditions [Tg] Value Unit I
BLOCKING VORM/VRRAn Repetitive peakvoltage 125 1600 V VDSMNRS~ Non-repetitive peak voltage 125 1700 V :DRM/IR;RPvi Repetitive peakcurrent 125 50 mA CONDUCTING .ITIiT(RMS.i Maximum continuous RMS current 50 Hz, Q = 4 l/min, water temperature = 400C 1550 A .itilT.SK Surge on-state current Max peak one cycle sine wave, 10 ms. 125 24.6 kA Without reverse voltage reapplied 2i..; 12 t 3026 x1E3 A2S V TM Max peak on-state voltage ITM = 2192A 125 1.39 V V T(TO) Threshold voltage 125 0.92 V
r T On-state slope resistance 125 0.216 mQ
SWITCHING d:ild;l; Critical rate of rise of on-state current, min. From 75% VDRM up t0 1650 A, gate 10 V - 5 Q 125 200 A/ps ~ Crifirnl rato nf rico nf nff_ctnto unltano min I ino:ar ranin iin fn 7fl9 nf \iriRM 1 9fi finn \//iic
GATE V GT Gate trigger voltage VD=5 V 25 3.5 V GT Gate triggercurrent VD=5V 25 300 mA P GM Max peak gate power Pulse width 100 ps 25 150 W
MECHANICAL R tnO-w) Thermal impedence, DC Junction to water (double side cooled) 0.13 0C/W 0 1s(RMS: Insulation voltage rms l min 25 2.5 kV Press Max water pressure 10 bar Tj max Max operating junction temperature 125 0C Weight 8000 g Thermal switch open 630C, cloused 500C. 10 A - 250 V OUTLINE Wl DEVICES TYPE:AT1004
SPRING			A	160
	i 0125__
	j@? j@?		B	6
<	]		c	70
	',~-~~ }		D	250
i	+ + -l		E	150
j			F G	84 50
		T	SPRING	2+2
	I I .
.l I v I I { -1,5 ' . 7
ORDERING INFORMATION : 2-2W51-AT1004 S 16 J L VDRM&\ standard specification . M&VRRM/100

SY100EP140LZI Price

*NOTE: 1. BRSW modes is enabled by setting A9 "High" at MRS (Mode Register Set). At the BRSW Mode, the burst length at write is fixed to "1" regardless of programmed burst length. 2. When BRSW write command with auto precharge is executed, keep it in mind that tRAS should not be violated Auto precharge is executed at the burst-end cycle, so in the case of BRSW write command, the next cycle starts the precharge.
SY100EP140LZI on stock

Represented by max _ioC
			J
		7



	f\|
l	l
\|l


16 VIF in l IF signal after SAW filter is input. 17 VIF in 2 It is balance-type input. j	L	1 L I	o

	L 7 7	L vr 7:

Suppliers Datasheet
		Exact Matc