TPS3808G125DBVRG4 Datasheet Precision Fixed Operating Frequency KAIM0280RB (67kHz) , KAIH0280RB (lOOkHz) Pulse by Pulse Over Current Limiting Over Load Protection Over Voltage Protection (Min. 23V) Intemal Thermal Shutdown Function Under Voltage Lockout Internal High Voltage Sense FET Auto Restart TPS3808G125DBVRG4 Price| | | TS555C-TS5551: | -S555M | | | Symbol | Parameter | Min | Typ | Max | Unit | | lcc | Supply Current (no load, High and Low States) Tamb = +250C Tmin. " Tamb " Tmax. | | 1 10 | 250 250 | cCA | | VCL | Control Voltagen. Tamb = +250C Tmin. " Tamb " Tmax. | 2.9 2.8 | 3.3 | 3.8 3.9 | V | | Vdis | Discharge Saturation Voltage (ldis = 10mA) Tamb = +250C Tmin. " Tamb " Tmax. | | 0.2 | 0.3 0.35 | V | | VOL | Low Level Outpnut Voltage (lsink = 8mA) Tamb = +250C Tmin. " Tamb " Tmax. | | 0.3 | 0.6 0.8 | V | | VOH | High Level OutRut Voltage (lsource = -2mA) Tamb = +250C Tmin. " Tamb " Tmax. | 4.4 4.4 | 4.6 | | V | | Vtrig | Trigger Voltage n. Tamb = +250C Tmin. " Tamb " Tmax. | 1.36 1.26 | 1.67 | 1.96 2.06 | V | | ltrig | Trigger Current | | 10 | | pA | | ITH | Threshold Current | | 10 | | pA | | Vreset | Reset Voltage _n. Tamb = +250C Tmin. " Tamb " Tmax. | 0.4 0.3 | 1.1 | 1.5 2.0 | V | | lreset | Reset Current | | 10 | | pA | | ldis | Discharge Pin Leakage Current | | 1 | 100 | nA | | | | | | |
TPS3808G125DBVRG4 on stock| | | TEST CONDITION | | | | | | PARAMETER | SYWBOL | | INPUT | OUT | | SP | HP | MIN | TYP | MAX | UNIT | | L | R | PUT | MODE | VR | VR | | Maximum Input Voltage | VIM1 | f=lkHz THD=1% | VIN 0 | O VIN | L R | Bypass | | | | -2.0 (790) | | | | VIM2 | f=lOOHz THD=1% | VIN 0 | O VIN | L R | 2SP | MAX | | | -16.0 060) | | | VIM3 | f=lOOHz THD=1% | VIN 0 | O VIN | L R | HP | | MAX | | -16.0 (1 60) | | | VIM4 | f=lOOHz THD=1% | VIN | O | L | 1SP | MAX | | | -16.0 (1 60) | | | VIM5 | f=lOOHz THD=1% | 0 | VIN | L | 1SP | MAX | | | -14.5 090) | | dBV | | VIM6 | V+=1.8V,f=1kHz THD=1% | VIN 0 | O VIN | L R | Bypass | | | -10.5 | -8.5 (380) | | m | | VIM7 | V+=1.8V,f=100Hz THD=1% | VIN 0 | O VIN | L R | 2SP | MAX | | -24.5 (60) | -22.5 (75) | | | VIM8 | V+=1.8V,f=100Hz THD=1% | VIN 0 | O VIN | L R | HP | | MAX | -24.5 (60) | -22.5 (75) | | | VIM9 | V+=1.8V,f=100Hz THD=1% | VIN | O | L | 1SP | MAX | | -24.5 (60) | -22.5 (75) | | | VIM10 | V+=1.8V,f=100Hz THD=1% | 0 | VIN | L | 1SP | MAX | | -23.0 (70) | -21.0 (90) | | | Output Noise | VN01 | Rg=0 A-Wegrk?d | 0 | O | L R | Bypass | | | | -112 (25) | -106 (5.0) | | | VN02 | Rg=0 A-Wegt3d | 0 | O | L R | 1SP | MAX | | | -100 00) | -94 (20) | dBV | | VN03 | Rg=0 A-Wegt3d | 0 | O | L R | HP | | MAX | | -100 00) | -94 (20) | (cA/rms) | | VN04 | Rg=0 | 0 | O | L | 1SP | MAX | | | -100 00) | -94 (20) | | | | | | | | | | | | | |
| Pin No. | Symbol | l/0 | Description | | 63 | ERR | I | Error: This signal goes low when the line printer has encountered an error conditionr | | 58 | SLIN | l/o | Line Printer Select: This signal is used to select the printer when it isilow. | | 57 | INIT | iro | Line Printer fnitialize: When this signaF goes low, it will allow the line printer initialiZjtion routine to be started. | | 56 | AFD | I/O | Line Printer Autofeed: When this signal goes low, it will cause the printer to line-feed after a lcne is printed. | | 55 | STB | l/0 | . Lin Printer Strob: When this signal is lowr it provides the line printer a signal to latch the data currently on the parallel port. This signal should keep low at least 0.5 ps to ensure the comple- tion of data latch. | | 45, 60 | INTO INT1 | 0 | Serial Channel Interrupts: Each Serial channel interrupt goes high when one of the following interrupts has an active condition and is enabled by the IER of its associated channel: Receiver Error Flag, Receiver Data Available, Transmitter Holding Register Empty,and Modem Status. The interrupt is reset to low upon appropriate service. This pin will be held in a high-impedance state if the MCR (3J of each associated channel is programmed low (logiC O). | | 59 | INT2 | O | Line Printer Interrupt: This interrupt goes low when ACK goes low. This signal is enabled by Bit 4 0f the Printer Control Register and will be held in a high-impedance state if Bit 4 0f the printer Control Register is programmed low. | | 23, 40, 64 | Vcc | I | Power Supply: +5V | | 2,7,9,22, 27, 42,43,54,61 | GND | | Ground: OV | | | | |
|
