TPS54920RHFT，there are the best TPS54920RHFT suppiers all over the world here.These are the list and detailed contact method of TPS54920RHFT suppliers all over the world as follows.You can buy or get informations of TPS54920RHFT through email , message or tel.

suppliers of TPS54920RHFT and PDF data of TPS54920RHFT

Part Numbert

Mfg

Packt

D/C

Descriptiont

Qty

Company/Contact

TPS54920RHFT Datasheet

Automatic Standby. When in Read mode, after 150ns of bus inactivity and when CMOS levels are driving the addresses, the chip automatically en- ters a pseudo-standby mode where consumption is reduced to the CMOS standby value, while out- puts still drive the bus.
TPS54920RHFT Price

PER SINGLE ELEK				EN
j j
	3600
RESIST		VE
-INDUCTIVE LOAD I

		0=30	6(	)	900	12(	)0	1	300

TPS54920RHFT on stock

* Package 3.2x1.6xl.lmm (1206) standard package * Feature of the device extremely wide viewing angle; ideal for backlighting and coupling in light guides * Wavelength 640 nm (red), 625 nm (red) 605 nm (orange), 590 nm (amber), 573nm (green), 525 nm (true green), 470 nm (blue) ~ Viewing angle Extremely Wide (1300) * Technology AIGaAs (red) GaAsP (orange) GaP (green, yellow) AlInGaP (red, orange, amber, green) InGaN (True green, blue) ~ Grouping parameter luminous intensity * Assembly methods suitable for all SMT assembly methods * Soldering methods IR reflow soldering * Preconditioning acc. to JEDEC Level 2 * Taping 8-mm tape with 3000/reel, +178mm

Pin Name	Pin Type	Description	Circuit Type	Number	Share Pin
PO.O PO.1 P0.2 P0.3	I/O	4-bit l/0 port. 1-bit and 4-bit read/write and test are possible. Individual pins are software configurable as input or output. Individual pins are software configurable as open- drain or push-pull output. Individual pull-up resistors are software assignable; pull-up resistors are automatically disabled for output pins.	E-1	1 1 1 0 g 8	TCLOO/KO TCLOO/K1 CLO/BUZ/K2 BUZ/K3
P1.0 P1 .1 P1.2 P1.3	I/O	Same as port 0.	E-1	7 6 5 4	INTO INT1 INT2 INT4
INTO, INT1	I/O	External interrupts. The triggering edge for INTO and INTl is selectable.		7.6	P1.0P1.1
INT2	I/O	Quasi-interrupt with detection of rising or falling edges		5	P1.2
INT4	I/O	External interrupt with detection of rising or falling edges.		4	P1.3
BUZ	I/O	2 kHz, 4 kHz, 8 kHz or 16 kHz frequency output for buzzer sound.		8	P0.3/K3
BUZ	I/O	Inverted BUZ signal		g	P0.2/CLO/K2
CLO	I/O	Clock output		9	P0.2/BUZ/K2
TCLOO	I/O	Inverted Timer/counter o clock output		1 0	PO.1/K1
TCLOO	I/O	Timer/counter o clock output		1 1	PO.O/KO
COMO-COM15	O	LCD common signal output	H-6	39-24
SEGO-SEG43	O	LCD segment signal output	H-6	40-80 1-3

Suppliers Datasheet
		Exact Matc